UNDER DEVELOPMENT

1 AUGUST 2026 - 30 SEPTEMBER 2026

No.

Title of DMS

Scope

NSC 19 - ELECTRICAL AND ELECTRONICS EQUIPMENT AND ACCESORIES

DMS IEC 60068-2-13:2021

Environmental testing – Part 2-13: Tests – Test M: Low air pressure
(IEC 60068-2-13:2021, IDT)

This part of IEC 60068 specifies methods of test applicable to specimens which, during transportation, storage or in service, can be subjected to low air pressure.

The object of the low air pressure test is to determine the ability of components, equipment or other articles to be used, transported or stored at low air pressure.

Components, equipment or other articles to be used, transported or stored under a simultaneous combination of high or low temperature and low air pressure, where the combination is important for the stresses imposed on the articles or for the failure mechanisms, are then tested in accordance with IEC 60068-2-39.

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

DMS IEC 60068-2-14:2023

Environmental testing –Part 2-14: Tests – Test N: Change of temperature
(IEC 60068-2-14:2023, IDT)

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

DMS IEC 60068-2-17:2023

Environmental testing – Part 2-17: Tests – Test Q: Sealing
(IEC 60068-2-17:2023, IDT)

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

UNDER DEVELOPMENT

15 AUGUST 2026 - 14 OCTOBER 2026

No.

Title of DMS

Scope

NSC 23 - OCCUPATIONAL SAFETY AND HEALTH

DMS ISO/DIS 45001

Occupational
health and safety
management
systems —
Requirements with
guidance for use

This document specifies requirements for an occupational health and safety (OH&S) management system, to enable organizations to provide safe and healthy workplaces by preventing work-related injury, and ill health, as well as by proactively improving its OH&S performance.

This document is applicable to any organization that wishes to establish, implement and maintain an OH&S management system to improve OH&S, eliminate hazards, minimize OH&S risks, take advantage of OH&S opportunities, and address OH&S management system nonconformities associated with its activities and promote work-related well-being.

This document helps an organization to achieve the intended results of its OH&S management system which include:

a) continual improvement of OH&S performance;
b) fulfilment of legal requirements and other requirements;
c) achievement of OH&S objectives.

This document is applicable to any organization regardless of its size, type and activities. It is applicable to the OH&S risks under the organization’s control, and OH&S opportunities, taking into account factors such as the context in which the organization operates and the needs and expectations of its workers and other interested parties.

This document does not state specific criteria for OH&S performance, nor is it prescriptive about the design of an OH&S management system.

This document does not address issues such as product safety, property damage or environmental impacts, beyond the OH&S risks to workers and other relevant interested parties.

This document can be used in whole or in part to systematically improve occupational health and safety management. However, claims of conformity to this document are not acceptable unless all its requirements are incorporated into an organization’s OH&S management system and fulfilled without exclusion. 

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

NSC 25 - QUALITY AND MANAGEMENT ORGANISATION

DMS ISO 9000:2026

Quality
management systems —
Fundamentals and vocabulary
(ISO 9000:2026, IDT)

This document establishes the fundamental concepts and principles of quality management which are universally applicable to the following:

— organizations seeking sustained success through the implementation of a quality management system (QMS);

— customers seeking confidence in an organization’s ability to consistently provide products and services conforming to their requirements;

— organizations seeking confidence in their supply chain that product and service requirements will be met;

— organizations and interested parties seeking to improve communication through a common understanding of the vocabulary used in quality management;

— organizations performing conformity assessments against the requirements of ISO 9001;

— providers of training, assessment or advice in quality management;

— developers of related standards.

This document defines terms that apply to all quality management documents and QMS standards developed by ISO/TC 176.

This document is applicable to all organizations, regardless of size, complexity or business model.

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

UNDER DEVELOPMENT

1 SEPTEMBER 2026 - 31 OCTOBER 2026

No.

Title of DMS

Scope

 NSC 06 - MECHANICAL ENGINEERING

DMS 966

Playground equipment – Safety performance for public use – Specification

This Malaysian Standard specifies safety andperformance requirements for public outdoor playground equipment designed for 5th percentile of a 2-year-old to the 95th percentile of a 12-year-old to reduce life-threatening and debilitating injuries. It excludes residential play equipment, toys, amusement rides, sports or fitness equipment for users over 12, specialized equipment for infants aged 6 to 24 months, soft contained play structures, and site furnishings outside the use zone (such as benches and shade
structures).

UPC

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

UNDER DEVELOPMENT

15 SEPTEMBER 2026 - 14 NOVEMBER 2026

No.

Title of DMS

Scope

 NSC 05 - ELECTRICAL AND ELECTRONICS EQUIPMENTS AND ACCESSORIES

DMS IEC 60598-2-1:2020

Luminaires – Part 2-1: Particular requirements – Fixed general purpose luminaires (IEC 60598-2-1:2020, IDT)

This document specifies requirements for fixed general purpose luminaires for use with electric light sources on supply voltages not exceeding 1000 V.

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

DMS IEC 60598-2-2:2023

Luminaires – Part 2-2: Particular requirements – Recessed luminaires and recessed air-handling luminaires (IEC 60598-2-2:2023, IDT)

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

DMS IEC 60598-2-5:2015

Luminaires – Part 2-5: Particular requirements – Floodlights (IEC 60598-2-5:2015, IDT)

This document specifies requirements for floodlights for use with electrical light sources on supply voltages not exceeding 1000V.

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

UNDER DEVELOPMENT

1 NOVEMBER 2026 - 30 NOVEMBER 2026

No.

Title of DMS

Scope

NSC 12 - TRANSPORT

DMS 2773

Motor vehicle ― Requirements for integrated automotive workshop ― Classification

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

NSC 18 - MEDICAL DEVICES AND FACILITIES FOR HEALTHCARE

DMS 2058

Code of practice for good engineering maintenance management of medical equipment in healthcare delivery organisation

UPC

DOCUMENT

PUBLIC COMMENT FORM

Email: pc[at]jsm[dot]gov[dot]my

1 AUGUST 2026 - 30 SEPTEMBER 2026

No.

MS Number

Title

NSC Approval Date

Justification for Withdrawal

NSC 04 - BUILDING AND CIVIL ENGINEERING WORKS

1

MS ISO 6240:2011

Performance standards in building – Contents and presentation (ISO 6240:1980, IDT)

12 November 2025

MS ISO 6240:2011, which is identical to ISO 6240:1980, has become outdated following the withdrawal of the international standard by the International Organization for Standardization (ISO) in October 2016. NSC 04 has agreed to withdraw MS ISO 6240:2011 without replacement, as it is obsolete and no longer aligned with current industry practices in Malaysia.

MS ISO 6241:2011

Performance standards in building – Principles for their preparation and factors to be considered (ISO 6241:1984, IDT)

12 November 2025

MS ISO 6241:2011, which is identical to ISO 6241:1984, has become outdated following the withdrawal of the international standard by the International Organization for Standardization (ISO) in October 2016. NSC 04 has agreed to withdraw MS ISO 6241:2011 without replacement, as it is obsolete and no longer aligned with current industry practices in Malaysia

1 OCTOBER 2026 - 30 NOVEMBER 2026

No.

MS Number

Title

NSC Approval Date

Justification for Withdrawal

NSC 18 - MEDICAL DEVICES AND FACILITIES FOR HEALTHCARE

1

MS 2059:2008 (confirmed:2013)

Medical laboratories — Guidance on laboratory implementation of MS ISO 15189:2014

18 August 2026

NSC 18/TC 7 reviewed and proposed for the MS to be withdrawn without replacement as this guidance document is also no longer referenced or utilized by stakeholders as well as the Accreditation Division of JSM has issued supplementary accreditation requirements detailing the accreditation requirements based on the MS ISO 15189 standard.

MS ISO 23640:2013 (confirmed:2020)

In vitro diagnostic medical devices — Evaluation of stability of in vitro diagnostic reagents (ISO 23640:2011, IDT)

NSC 18/TC 7 reviewed and proposed for the MS to be withdrawn without replacement as currently, industry alignment with broader technical evaluation frameworks.

MS ISO 11554:2019

Optics and photonics — Lasers and laser —related equipment — Test methods for laser beam power, energy and temporal characteristics (ISO 11554:2017, IDT)

NSC 18/TC 11 has reviewed the MS and proposed its withdrawal without replacement, as it have been superseded by an updated version, ISO 11554:2025 and due to no longer referred by local stakeholders & industries.

MS IEC 60601-2-33:2009

Medical electrical equipment — Part 2-33: Particular requirements for the safety of magnetic resonance equipment for medical diagnostic (IEC 60601-2-33:2002, AMD. 1:2005, IDT)

NSC 18/TC 11 has reviewed the MS and proposed its withdrawal without replacement,  NSC 18/TC 11 has reviewed the MS and proposed its withdrawal without replacement, as MS is no longer referred by local stakeholders & industries.