FAQ
Contact Us
Feedback & Complaint
Sitemap
PUBLIC
STAFFPublic Comment is an important step in developing the Malaysian Standard (MS). Aligned with Article 4 and Annex 3 of The WTO TBT Agreement, the Department of Standards Malaysia (JSM) invites all parties to share feedback or comment on draft MS that covers new, revision, amendment and the withdrawal of MS. All comments received will be reviewed and discussed by the relevant committee under the purview of JSM.
For further information on public comment, please contact:
Public Comment Team
Standardisation Division
Department of Standards Malaysia
CYBERJAYA
E-mel: pc[at]jsm[dot]gov[dot]my
-
No Title Download 1 Public Comment for Under Development PDF -
1 AUGUST 2026 - 30 AUGUST 2026
UNDER DEVELOPMENT
1 AUGUST 2026 - 30 SEPTEMBER 2026
No.
Title of DMS
Scope
Details NSC 14 - RUBBER AND RUBBER PRODUCTS
1. DMS 1359-7:202X
Test method for raw natural
rubber — Part 7:
Determination of Mooney
accelerated storage
hardening test (MASHT)This document specifies a method of measuring the storage hardening of raw natural rubber using the Mooney shearing disc viscometer. Email: pc[at]jsm[dot]gov[dot]my
2. DMS 1359-8:202X
Test methods for raw
natural rubber - Part 8:
Determination of Wallace
accelerated storage
hardening test (WASHT)This document specifies a method of measuring the Wallace accelerated storage-hardening of raw natural rubber. Email: pc[at]jsm[dot]gov[dot]my
-
1 AUGUST 2026 - 30 SEPTEMBER 2026
UNDER DEVELOPMENT
1 AUGUST 2026 - 30 SEPTEMBER 2026
No.
Title of DMS
Scope
Details NSC 19 - ELECTRICAL AND ELECTRONICS EQUIPMENT AND ACCESORIES
1. DMS IEC 60068-2-13:2021
Environmental testing – Part 2-13: Tests – Test M: Low air pressure
(IEC 60068-2-13:2021, IDT)This part of IEC 60068 specifies methods of test applicable to specimens which, during transportation, storage or in service, can be subjected to low air pressure.
The object of the low air pressure test is to determine the ability of components, equipment or other articles to be used, transported or stored at low air pressure.
Components, equipment or other articles to be used, transported or stored under a simultaneous combination of high or low temperature and low air pressure, where the combination is important for the stresses imposed on the articles or for the failure mechanisms, are then tested in accordance with IEC 60068-2-39.
Email: pc[at]jsm[dot]gov[dot]my
2. DMS IEC 60068-2-14:2023
Environmental testing –Part 2-14: Tests – Test N: Change of temperature
(IEC 60068-2-14:2023, IDT)This document provides tests with specified ambient temperature changes to analyse their impacts on specimens. Email: pc[at]jsm[dot]gov[dot]my
3 DMS IEC 60068-2-17:2023
Environmental testing – Part 2-17: Tests – Test Q: Sealing
(IEC 60068-2-17:2023, IDT)This document deals with seal tests applicable to the external and internal detection in container sealing of gross leaks and fine leaks to determine the effectiveness of seals of specimens. For further tests to verify the ability of enclosures, covers and seals to maintain components and equipment in good working order, IEC 60068-2-18 can be helpful. Email: pc[at]jsm[dot]gov[dot]my
-
15 AUGUST 2026 - 31 AUGUST 2026
UNDER DEVELOPMENT
15 AUGUST 2026 - 31 AUGUST 2026
No.
Title of DMS
Scope
Details NSC 21 - FOOD, FOOD PRODUCTS AND FOOD SAFETY
1. DMS 682
This document specifies the requirements for cooking oils, specifically refined unblended palm olein cooking oil and non-palm cooking oil, for commercial and consumer use. It does not cover the requirements for blended cooking oil, red palm olein and used cooking oils.
Email: pc[at]jsm[dot]gov[dot]my
-
15 AUGUST 2026 - 14 OCTOBER 2026
UNDER DEVELOPMENT
15 AUGUST 2026 - 14 OCTOBER 2026
No.
Title of DMS
Scope
Details NSC 23 - OCCUPATIONAL SAFETY AND HEALTH
1. DMS ISO/DIS 45001
Occupational
health and safety
management
systems —
Requirements with
guidance for useThis document specifies requirements for an occupational health and safety (OH&S) management system, to enable organizations to provide safe and healthy workplaces by preventing work-related injury, and ill health, as well as by proactively improving its OH&S performance.
This document is applicable to any organization that wishes to establish, implement and maintain an OH&S management system to improve OH&S, eliminate hazards, minimize OH&S risks, take advantage of OH&S opportunities, and address OH&S management system nonconformities associated with its activities and promote work-related well-being.
This document helps an organization to achieve the intended results of its OH&S management system which include:
a) continual improvement of OH&S performance;
b) fulfilment of legal requirements and other requirements;
c) achievement of OH&S objectives.This document is applicable to any organization regardless of its size, type and activities. It is applicable to the OH&S risks under the organization’s control, and OH&S opportunities, taking into account factors such as the context in which the organization operates and the needs and expectations of its workers and other interested parties.
This document does not state specific criteria for OH&S performance, nor is it prescriptive about the design of an OH&S management system.
This document does not address issues such as product safety, property damage or environmental impacts, beyond the OH&S risks to workers and other relevant interested parties.
This document can be used in whole or in part to systematically improve occupational health and safety management. However, claims of conformity to this document are not acceptable unless all its requirements are incorporated into an organization’s OH&S management system and fulfilled without exclusion.
Email: pc[at]jsm[dot]gov[dot]my
-
1 AUGUST 2026 - 30 AUGUST 2026
-
-
15 JULY 2026 - 14 SEPTEMBER 2026
15 JULY 2026 - 14 SEPTEMBER 2026
No.
MS Number
Title
NSC Approval Date
Justification for Withdrawal
NSC 19 - ELECTRICAL AND ELECTRONICS EQUIPMENT AND ACCESORIES
1
MS 2085:2008
Domestic and similar electronic equipment interconnection requirements - Peritelevision connector (BS EN 50049-1:1998)
10 February 2026
MS 2085:2008 which is technically identical to BS EN 50049-1:1998 has become outdated following the withdrawal of the international standard by British Standards Institution (BSI) in 2014. As a result, the standard is no longer applied by industry in Malaysia.
Therefore, NSC 19 has agreed to withdraw MS 2085:2008 without replacement.2 MS IEC 60107-1:2008 Methods of measurement on receivers for television broadcast transmissions - Part 1: General considerations - Measurements at radio and video frequencies (IEC 60107-1:1997, IDT) 10 February 2026 MS IEC 60107-1:2008 which is identical to IEC 60107-1:1997 is technologically obsolete and no longer aligned with current industry requirements.
Therefore, NSC 19 has agreed to withdraw MS IEC 60107-1:2008 without replacement.3 MS IEC 60598-2-9:2001 Luminaires - Part 2: Particular requirements section nine - Photo and film luminaires (Non-professional) (IEC 60598-2-9:1987, AMD. 1:1993, IDT) 9 February 2026 MS IEC 60598-2-9:2001 which is identical to IEC 60598-2-9:1987+AMD. 1:1993 has become outdated following the withdrawal of the international standard by the International Electrotechnical Commission (IEC) in October 2019. As a result, the standard is no longer applied by industry in Malaysia.
Therefore, NSC 19 has agreed to withdraw MS IEC 60598-2-9:2001 without replacement.4 MS IEC 60598-2-24:2006 Luminaires – Part 2-24: Particular requirements – Luminaires with limited surface temperatures (IEC 60598-2-24:1997, IDT) 9 February 2026 MS IEC 60598-2-24:2006 which is identical to IEC 60598-2-24:1997 has become outdated following the withdrawal of the international standard by the International Electrotechnical Commission (IEC) in June 2013. As a result, the standard is no longer applied by industry in Malaysia.
Therefore, NSC 19 has agreed to withdraw MS IEC 60598-2-24:2006 without replacement.
5 MS IEC 60966-3-2:2007 Radio frequency and coaxial cable assemblies - Part 3-2: Detail specification for semi-flexible coaxial cable assemblies for GSM use (0,8 GHz - 1 GHz) (First Revision) (IEC 60966-3-2:2003, IDT) 10 February 2026 MS IEC 60966-3-2:2007 which is identical to IEC 60966-3-2:2003 is technologically obsolete and no longer aligned with current industry requirements.
Therefore, NSC 19 has agreed to withdraw MS IEC 60966-3-2:2007 without replacement. -
1 AUGUST 2026 - 30 SEPTEMBER 2026
1 AUGUST 2026 - 30 SEPTEMBER 2026
No.
MS Number
Title
NSC Approval Date
Justification for Withdrawal
NSC 04 - BUILDING AND CIVIL ENGINEERING WORKS
1
MS ISO 6240:2011
Performance standards in building – Contents and presentation (ISO 6240:1980, IDT)
12 November 2025
MS ISO 6240:2011, which is identical to ISO 6240:1980, has become outdated following the withdrawal of the international standard by the International Organization for Standardization (ISO) in October 2016. NSC 04 has agreed to withdraw MS ISO 6240:2011 without replacement, as it is obsolete and no longer aligned with current industry practices in Malaysia.
2 MS ISO 6241:2011
Performance standards in building – Principles for their preparation and factors to be considered (ISO 6241:1984, IDT)
12 November 2025
MS ISO 6241:2011, which is identical to ISO 6241:1984, has become outdated following the withdrawal of the international standard by the International Organization for Standardization (ISO) in October 2016. NSC 04 has agreed to withdraw MS ISO 6241:2011 without replacement, as it is obsolete and no longer aligned with current industry practices in Malaysia
-
15 JULY 2026 - 14 SEPTEMBER 2026